@ -256,6 +256,57 @@ The function computes an inverse affine transformation represented by
The result is also a
:math:`2 \times 3` matrix of the same type as ``M`` .
LinearPolar
-----------
Remaps an image to polar space.
..ocv:cfunction:: void cvLinearPolar( const CvArr* src, CvArr* dst, CvPoint2D32f center, double maxRadius, int flags=CV_INTER_LINEAR+CV_WARP_FILL_OUTLIERS )
:param src:Source image
:param dst:Destination image
:param center:The transformation center;
:param maxRadius:Inverse magnitude scale parameter. See below
:param flags:A combination of interpolation methods and the following optional flags:
* **CV_WARP_FILL_OUTLIERS** fills all of the destination image pixels. If some of them correspond to outliers in the source image, they are set to zero
* **CV_WARP_INVERSE_MAP** See below
The function ``cvLinearPolar`` transforms the source image using the following transformation:
*
Forward transformation (``CV_WARP_INVERSE_MAP`` is not set):
..math::
dst( \phi , \rho ) = src(x,y)
*
Inverse transformation (``CV_WARP_INVERSE_MAP`` is set):
@ -504,7 +504,7 @@ Fills a connected component with the given color.
:param image:Input/output 1- or 3-channel, 8-bit, or floating-point image. It is modified by the function unless the ``FLOODFILL_MASK_ONLY`` flag is set in the second variant of the function. See the details below.
:param mask:(For the second function only) Operation mask that should be a single-channel 8-bit image, 2 pixels wider and 2 pixels taller. The function uses and updates the mask, so you take responsibility of initializing the ``mask`` content. Flood-filling cannot go across non-zero pixels in the mask. For example, an edge detector output can be used as a mask to stop filling at edges. It is possible to use the same mask in multiple calls to the function to make sure the filled area does not overlap.
:param mask:Operation mask that should be a single-channel 8-bit image, 2 pixels wider and 2 pixels taller than ``image``. Since this is both an input and output parameter, you must take responsibility of initializing it. Flood-filling cannot go across non-zero pixels in the input mask. For example, an edge detector output can be used as a mask to stop filling at edges. On output, pixels in the mask corresponding to filled pixels in the image are set to 1 or to the a value specified in ``flags`` as described below. It is therefore possible to use the same mask in multiple calls to the function to make sure the filled areas do not overlap.
..note:: Since the mask is larger than the filled image, a pixel :math:`(x, y)` in ``image`` corresponds to the pixel :math:`(x+1, y+1)` in the ``mask`` .
@ -518,11 +518,11 @@ Fills a connected component with the given color.
:param rect:Optional output parameter set by the function to the minimum bounding rectangle of the repainted domain.
:param flags:Operation flags. Lower bits contain a connectivity value, 4 (default) or 8, used within the function. Connectivity determines which neighbors of a pixel are considered. Upper bits can be 0 or a combination of the following flags:
:param flags:Operation flags. The first 8 bits contain a connectivity value. The default value of 4 means that only the four nearest neighbor pixels (those that share an edge) are considered. A connectivity value of 8 means that the eight nearest neighbor pixels (those that share a corner) will be considered. The next 8 bits (8-16) contain a value between 1 and 255 with which to fill the ``mask`` (the default value is 1). For example, ``4 | ( 255 << 8 )`` will consider 4 nearest neighbours and fill the mask with a value of 255. The following additional options occupy higher bits and therefore may be further combined with the connectivity and mask fill values using bit-wise or (``|``):
* **FLOODFILL_FIXED_RANGE** If set, the difference between the current pixel and seed pixel is considered. Otherwise, the difference between neighbor pixels is considered (that is, the range is floating).
* **FLOODFILL_MASK_ONLY** If set, the function does not change the image ( ``newVal`` is ignored), but fills the mask. The flag can be used for the second variant only.
* **FLOODFILL_MASK_ONLY** If set, the function does not change the image ( ``newVal`` is ignored), and only fills the mask with the value specified in bits 8-16 of ``flags`` as described above. This option only make sense in function variants that have the ``mask`` parameter.
The functions ``floodFill`` fill a connected component starting from the seed point with the specified color. The connectivity is determined by the color/brightness closeness of the neighbor pixels. The pixel at
:math:`(x,y)` is considered to belong to the repainted domain if:
:param image:Source, an 8-bit single-channel image. Non-zero pixels are treated as 1's. Zero pixels remain 0's, so the image is treated as ``binary`` . You can use :ocv:func:`compare` , :ocv:func:`inRange` , :ocv:func:`threshold` , :ocv:func:`adaptiveThreshold` , :ocv:func:`Canny` , and others to create a binary image out of a grayscale or color one. The function modifies the ``image`` while extracting the contours.
:param image:Source, an 8-bit single-channel image. Non-zero pixels are treated as 1's. Zero pixels remain 0's, so the image is treated as ``binary`` . You can use :ocv:func:`compare` , :ocv:func:`inRange` , :ocv:func:`threshold` , :ocv:func:`adaptiveThreshold` , :ocv:func:`Canny` , and others to create a binary image out of a grayscale or color one. The function modifies the ``image`` while extracting the contours. If mode equals to ``CV_RETR_CCOMP`` or ``CV_RETR_FLOODFILL``, the input can also be a 32-bit integer image of labels (``CV_32SC1``).
:param contours:Detected contours. Each contour is stored as a vector of points.
Hernan Badino
11 years ago