If set, and if TCP is available as RTSP RTP transport, then TCP will be
tried first as RTP transport.
Signed-off-by: Michael Niedermayer <michaelni@gmx.at>
An SDP description normally only contains the target IP address
and port for the packets. This means that we don't really have
any clue where to send the RTCP RR packets - previously they're
sent to the destination IP written in the SDP (at the same port),
which rarely is the actual peer. And if the source for the packets
is on a different port than the destination, it's never correct.
With a new option, we can choose to send the packets to the
address that the latest packet on each socket arrived from.
---
Some may even argue that this should be the default - perhaps,
but I'd rather keep it optional at first. Additionally, I'm not
sure if sending RTCP RR directly back to the source is
desireable for e.g. multicast.
Signed-off-by: Martin Storsjö <martin@martin.st>
Add support for domain names, for multiple source addresses,
for exclusions, and for session level specification of addresses.
Signed-off-by: Martin Storsjö <martin@martin.st>
This supports inclusion of one single IP address for now,
at the media level. Specifying the filter at the session level
(instead of at the media level), multiple source addresses,
exclusion, or using FQDNs instead of plain IP addresses is not
supported (yet at least).
Signed-off-by: Martin Storsjö <martin@martin.st>
Passes Source-Specific Multicast parameters read from an sdp file through to the UDP socket code,
allowing source-specific multicast streams to be correctly received. As an integral part of this
change, additional checking (currently only enabled in the case of SSM streams, but probably
useful in similar scenarios) has been added to the RTP protocol handler to distinguish UDP packets
arriving from multiple sources to the same port and process only the expected packets
(those transmitted from the expected UDP source address). This resolves an issue identified
when multiple instances of FFmpeg subscribe to different Source-Specific Multicast streams
but with each sharing the same destination port.
Signed-off-by: Edward Torbett <ed.torbett@simulation-systems.co.uk>
Signed-off-by: Michael Niedermayer <michaelni@gmx.at>
This only takes care of decrypting incoming packets; the outgoing
RTCP packets are not encrypted. This is enough for some use cases,
and signalling crypto keys for use with outgoing RTCP packets
doesn't fit as simply into the API. If the SDP demuxer is hooked
up with custom IO, the return packets can be encrypted e.g. via the
SRTP protocol.
If the SRTP keys aren't available within the SDP, the decryption
can be handled externally as well (when using custom IO).
Signed-off-by: Martin Storsjö <martin@martin.st>
This sends NACK for missed packets and PLI (picture loss indication)
if a depacketizer indicates that it needs a new keyframe, according
to RFC 4585.
This is only enabled if the SDP indicated that feedback is supported
(via the AVPF or SAVPF profile names).
The feedback packets are throttled to a certain maximum interval
(currently 250 ms) to make sure the feedback packets don't eat up
too much bandwidth (which might be counterproductive). The RFC
specifies a more elaborate feedback packet scheduling.
The feedback packets are currently sent independently from normal
RTCP RR packets, which is not totally spec compliant, but works
fine in the environments I've tested it in. (RFC 5506 allows this,
but requires a SDP attribute for enabling it.)
Signed-off-by: Martin Storsjö <martin@martin.st>
To use this, set sdpflags=custom_io to the sdp demuxer. During
the avformat_open_input call, the SDP is read from the AVFormatContext
AVIOContext (ctx->pb) - after the avformat_open_input call,
during the av_read_frame() calls, the same ctx->pb is used for reading
packets (and sending back RTCP RR packets).
Normally, one would use this with a read-only AVIOContext for the
SDP during the avformat_open_input call, then close that one and
replace it with a read-write one for the packets after the
avformat_open_input call has returned.
This allows using the RTP depacketizers as "pure" demuxers, without
having them tied to the libavformat network IO.
Signed-off-by: Martin Storsjö <martin@martin.st>
Streams from RTSP or SDP that do not match an allowed type will
be skipped entirely, which allows video-only or audio-only
streaming from servers that provide both.
Signed-off-by: Martin Storsjö <martin@martin.st>
Eventually, the old way of passing options by adding
stuff to the URL can be dropped.
This avoids having to tamper with the user-specified URL to
pass options on the transport mode. This also works better
with redirects, since the options don't need to be parsed out
from the URL.
Signed-off-by: Martin Storsjö <martin@martin.st>
This eases adding options that are common for both. The
AV_OPT_FLAG_EN/DECODING_PARAM still indicates whether they belong
to the muxer or demuxer.
Signed-off-by: Martin Storsjö <martin@martin.st>
This is more like what VLC does. If the server doesn't mention
supporting GET_PARAMETER in response to an OPTIONS request,
VLC doesn't send any keepalive requests at all. After this patch,
libavformat will still send OPTIONS keepalives if GET_PARAMETER
isn't explicitly said to be supported.
Some RTSP cameras don't support GET_PARAMETER, and will
close the connection if this is sent as keepalive request
(but support OPTIONS just fine, but probably don't need any
keepalive at all). Some other cameras don't support using
OPTIONS as keepalive, but require GET_PARAMETER instead.
Signed-off-by: Martin Storsjö <martin@martin.st>
Gilles Chanteperdrix
Luca Barbato
Andrey Utkin
Martin Storsjö
Ed Torbett
Carl Eugen Hoyos
Michael Niedermayer
Jordi Ortiz
Dmitry Volyntsev
Diego Biurrun
John Brooks
Anton Khirnov
Mans Rullgard
Diego Elio Pettenò