This makes the test stricter because it is checked that the
MMX registers are not accidentally clobbered.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
Only sub_media_pred has an MMXEXT version, so one can use
the version with the stricter check (that checks that
the MMX registers have not been clobbered) for sub_left_predict.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
Only the idct_dc and add_residual functions have MMX versions,
so one can use the version with the stricter check (that checks
that the MMX registers have not been clobbered) for all the other
checks.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
check_func() might return NULL, in which case the function is not to be
benched. Introduced in cc679054c7.
Signed-off-by: Matthias Dressel <code@deadcode.eu>
Signed-off-by: Martin Storsjö <martin@martin.st>
The code was blindly assuming that Zbb or V implied Zba. While the
earlier is practically always true, the later broke some QEMU setups,
as V was introduced earlier than Zba.
Add an optional filter_line3 to the available optimisations.
filter_line3 is equivalent to filter_line, memcpy, filter_line
filter_line shares quite a number of loads and some calculations in
common with its next iteration and testing shows that using aarch64
neon filter_line3s performance is 30% better than two filter_lines
and a memcpy.
Adds a test for vf_bwdif filter_line3 to checkasm
Rounds job start lines down to a multiple of 4. This means that if
filter_line3 exists then filter_line will not sometimes be called
once at the end of a slice depending on thread count. The final slice
may do up to 3 extra lines but filter_edge is faster than filter_line
so it is unlikely to create any noticable thread load variation.
Signed-off-by: John Cox <jc@kynesim.co.uk>
Signed-off-by: Martin Storsjö <martin@martin.st>
From x86inc:
> On AMD cpus <=K10, an ordinary ret is slow if it immediately follows either
> a branch or a branch target. So switch to a 2-byte form of ret in that case.
> We can automatically detect "follows a branch", but not a branch target.
> (SSSE3 is a sufficient condition to know that your cpu doesn't have this problem.)
x86inc can automatically determine whether to use REP_RET rather than
REP in most of these cases, so impact is minimal. Additionally, a few
REP_RETs were used unnecessary, despite the return being nowhere near a
branch.
The only CPUs affected were AMD K10s, made between 2007 and 2011, 16
years ago and 12 years ago, respectively.
In the future, everyone involved with x86inc should consider dropping
REP_RETs altogether.
This commit enabled assembly code with intel AVX512 VNNI and added unit test for sobel filter
sobel_c: 4537
sobel_avx512icl 2136
Signed-off-by: bwang30 <bin.wang@intel.com>
Signed-off-by: Haihao Xiang <haihao.xiang@intel.com>
There is no MMX code for (add|put|put_signed)_pixels_clamped
since commit bfb28b5ce8, so use
declare_func instead of declare_func_emms() to also test that
we are not in MMX mode after return.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
There is no MMX code for diff_bytes since commit
230ea38de1, so use declare_func
instead of declare_func_emms() to also test that we are not
in MMX mode after return.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
There is no MMX code for add_int16 since commit
4b6ffc2880, so use declare_func
instead of declare_func_emms() to also test that we are not
in MMX mode after return.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
There is no MMX code for llviddsp after commit
fed07efcde, so use declare_func
instead of declare_func_emms() to also test that we are not
in MMX mode after return.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
There is no MMX code for pixblockdsp after commit
92b5800277, so use declare_func
instead of declare_func_emms() to also test that we are not
in MMX mode after return.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
There is no MMX code for audiodsp after commit
3d716d38ab, so use declare_func
instead of declare_func_emms() to also test that we are not
in MMX mode after return.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
There is no MMX code for blockdsp after commit
ee551a21dd, so use declare_func
instead of declare_func_emms() to also test that we are not
in MMX mode after return.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
There is no MMX code for vc1_inv_trans_8x8 or
vc1_unescape_buffer, so use declare_func instead of
declare_func_emms() to also test that we are not in MMX
mode after return.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
There is no MMX code for loop filters since commit
6a551f1405, so use declare_func
instead of declare_func_emms() to also test that we are not
in MMX mode after return.
Reviewed-by: Ronald S. Bultje <rsbultje@gmail.com>
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
Unfortunately, it is common, and will remain so, that the Bit
manipulations are not enabled at compilation time. This is an official
policy for Debian ports in general (though they do not support RISC-V
officially as of yet) to stick to the minimal target baseline, which
does not include the B extension or even its Zbb subset.
For inline helpers (CPOP, REV8), compiler builtins (CTZ, CLZ) or
even plain C code (MIN, MAX, MINU, MAXU), run-time detection seems
impractical. But at least it can work for the byte-swap DSP functions.
RVV defines a total of 12 different extensions, including:
- 5 different instruction subsets:
- Zve32x: 8-, 16- and 32-bit integers,
- Zve32f: Zve32x plus single precision floats,
- Zve64x: Zve32x plus 64-bit integers,
- Zve64f: Zve32f plus Zve64x,
- Zve64d: Zve64f plus double precision floats.
- 6 different vector lengths:
- Zvl32b (embedded only),
- Zvl64b (embedded only),
- Zvl128b,
- Zvl256b,
- Zvl512b,
- Zvl1024b,
- and the V extension proper: equivalent to Zve64f and Zvl128b.
In total, there are 6 different possible sets of supported instructions
(including the empty set), but for convenience we allocate one bit for
each type sets: up-to-32-bit ints (RVV_I32), floats (RVV_F32),
64-bit ints (RVV_I64) and doubles (RVV_F64).
Whence the vector size is needed, it can be retrieved by reading the
unprivileged read-only vlenb CSR. This should probably be a separate
helper macro if needed at a later point.
This introduces compile-time and run-time CPU detection on RISC-V. In
practice, I doubt that FFmpeg will ever see a RISC-V CPU without all of
I, F and D extensions, and if it does, it probably won't have run-time
detection. So the flags are essentially always set.
But as things stand, checkasm wants them that way. Compare the ARMV8
flag on AArch64. We are nowhere near running short on CPU flag bits.
~4x faster than the C version.
The shuffles in the 15pt dim1 are seriously expensive. Not happy with it,
but I'm contempt.
Can be easily converted to pure AVX by removing all vpermpd/vpermps
instructions.
Old one was written with the assumption only even inputs would be given.
This very messy replacement supports even and odd inputs, and supports
AVX2 for extra speed. The buffers given are usually quite big (4k samples),
so the speedup is worth it.
The new SSE version is still faster than the old inline asm version by 33%.
Also checkasm is provided to make sure this monstrosity works.
This fixes some FATE tests.
Andreas Rheinhardt
Matthias Dressel
Rémi Denis-Courmont
John Cox
Martin Storsjö
Lynne
xufuji456
J. Dekker
James Darnley
bwang30
James Almer