The plain VP6 format is vertically flipped compared to VP6F/VP6A.
Support for the plain VP6 format was added in 09d8c0ae83 (which
also introduced support for muxing VP6F properly in general).
Signed-off-by: Martin Storsjö <martin@martin.st>
In these cases, there is no extradata but only the properly set
width/height values by the demuxer.
This makes sure VP6 in F4V files is cropped properly.
This is similar to what is done for H264 for letting the container
width/height override what's in the bitstream, since 30f515091.
Signed-off-by: Martin Storsjö <martin@martin.st>
This is in preparation for removing a .rodata kludge
which was only required for older YASM versions.
The movbe instruction was introduced in 0.8.0, which already
had AVX, which was introduced in 0.7.0, and NASM introduced
movbe in 2.0.3, which is the same version which introduced
AVX support.
Also, make the failure message more accurate.
Signed-off-by: Derek Buitenhuis <derek.buitenhuis@gmail.com>
Prevents a crash if the misaligned exception mask bit is
cleared for some reason.
Misaligned SSE functions are only used on AMD Phenom CPUs
and the benefit is miniscule. They also require modifying
the MXCSR control register and by removing those functions
we can get rid of that complexity altogether.
Signed-off-by: Derek Buitenhuis <derek.buitenhuis@gmail.com>
Store XMM6 and XMM7 in the shadow space in functions that
clobbers them. This way we don't have to adjust the stack
pointer as often, reducing the number of instructions as
well as code size.
Signed-off-by: Derek Buitenhuis <derek.buitenhuis@gmail.com>
SWAP with >=3 named (rather than numbered) args
PERMUTE followed by SWAP with 2 named args
used to produce the wrong permutation
Signed-off-by: Derek Buitenhuis <derek.buitenhuis@gmail.com>
The implementation of 25cb0c1a involves lots of spurious labels.
The effect of keeping those labels around is making debugging harder.
Those labels are meaningless, and complicate the disassembly. Also,
gdb can't tell the difference between them and function entry points.
This new strip command is irrelevant to any usage of Libav that would
have used the old fully stripped version, because the old one was for
non-debug use.
Signed-off-by: Derek Buitenhuis <derek.buitenhuis@gmail.com>
Now RET checks whether it immediately follows a branch, so the
programmer dosen't have to keep track of that condition. REP_RET
is still needed manually when it's a branch target, but that's
much rarer.
The implementation involves lots of spurious labels, but that's OK
because we strip them.
Signed-off-by: Derek Buitenhuis <derek.buitenhuis@gmail.com>
Lanczos for general case, sinc for upscaling, Gaussian for
downscaling. According to current literature these scalers
should be the best quality-wise algorithms for each case.
Inspired from a patch by wm4 <nfxjfg@googlemail.com>
Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
If the input file contains other tracks (non video/audio) that
aren't included in ismindex, the global file duration as returned
by libavformat might not be equal to the maximum of the duration
of the actual included tracks.
Signed-off-by: Martin Storsjö <martin@martin.st>
The stream duration is used for calculating the duration of the
last fragment easily without manually parsing anything else than
the mfra/tfra atoms. When the global file duration was used
previously, the duration of the last fragment could end up wrong
if the streams weren't equally long.
Signed-off-by: Martin Storsjö <martin@martin.st>
This wasn't an issue prior to 58404738, when the whole RTMP packet
was copied at once and the length of the individual embedded flv
packets only were validated by the flv demuxer.
Prior to this patch, this could lead to reads and writes out of bound.
Signed-off-by: Martin Storsjö <martin@martin.st>
If the embedded flv packets were incomplete and we aborted the
copying loop early, make sure the flv buffer is trimmed to
only contain full packets.
Signed-off-by: Martin Storsjö <martin@martin.st>