avdevice_register_all() is still required to register devices into
lavf (this is required due to lavd being somewhat of a hack).
Signed-off-by: Josh de Kock <josh@itanimul.li>
With certain types of input and the filter chain getting re-initialized
or re-configured, multiple nullptr AVSubtitles can get pushed into
sub2video_update() in a row from sub2video_heartbeat.
This causes end_pts, and on the next round pts, to become INT64_MAX,
latter of which signals EOF in framesync, leading to complete loss of
subtitles from that point on.
Thus, check that the sub2video.end_pts is smaller than INT64_MAX
in a similar fashion to sub2video_flush before sending out the
nullptr AVSubtitle. This keeps premature EOFs from happening in
framesync and the subtitle overlay is kept past the filter chain
re-initializations/configurations.
The generic code should be able to finish the streams just fine initializing
and flushing the filters and codecs properly.
Fixes the following command:
ffmpeg -f lavfi -i "testsrc=d=0.1[out0];aevalsrc=0:d=0[out1]" -af apad -shortest -f framecrc -
Signed-off-by: Marton Balint <cus@passwd.hu>
Should prevent unnecessary copy of data in cases where new references
to the packet are created within the muxer or a bitstream filter.
Reviewed-by: Michael Niedermayer <michael@niedermayer.cc>
Signed-off-by: James Almer <jamrial@gmail.com>
It's been a noop for years, and it's been argued that in-band headers
should not be forcedly removed without the user's explicit request.
Also, as the FIXME line stated, this is a job for a bitstream filter
like extract_extradata, remove_extradata, dump_extradata, and
filter_units.
Signed-off-by: James Almer <jamrial@gmail.com>
When a decoded stream is being looped, after each post-EOF rewind,
decoders are flushed in seek_to_start(). This only drains 1 frame, and
thus the output has a few frames missing at the tail of each iteration
except the last.
With this patch, process_input is looped till process_input_packet
reaches EOF.
Fixes#7081
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
On systems which deliver SIGPIPE (Unices), a broken pipe will currently
result in the immediate termination of the ffmpeg process (the default
disposition as required by POSIX). This is undesirable, because while
the broken pipe is likely fatal to useful cleanup of whatever component
is writing to it, there might be other components which can do useful
cleanup - for example, a muxer on another stream may still need to write
indexes to complete a file. Therefore, set the signal disposition for
SIGPIPE to ignore the signal - the call which caused the signal will
fail with EPIPE and the error will be propagated upwards like any other
I/O failure on a single stream.
add return value check to supress the build warning message like
"warning: ignoring return value" when use attribute -Wunused-result.
Signed-off-by: Jun Zhao <jun.zhao@intel.com>
Reviewed-by: 刘歧 <lq@chinaffmpeg.org>
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
With there being two hwaccels that use the CUDA pix_fmt now, just
relying on the pix_fmt to identify the selected hwaccel is not enough
anymore.
So this checks if the user explicitly selected a hwaccel, and only
accepts that one.
Fixes looping files without audio or when using stream_copy, where
ist->nb_samples is not set since no decoding is done.
This fixes ticket #5719 and also fixes an endless loop with the sample
in ticket #6139.
Signed-off-by: Peter Große <pegro@friiks.de>
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
Since a7da134742, flush packets are passed
to process_input_packet() during stream copy. This modifies the input
timestamp handling to ignore them - since they contain no data, timestamps
should not be affected.
Otherwise the frame size of the codec is not set in the buffersink.
Fixes ticket #6603 and the following simpler case:
ffmpeg -c aac -filter_complex "sine=d=0.1,asetnsamples=1025" out.aac
Signed-off-by: Marton Balint <cus@passwd.hu>
This is required for FLV files, for which duration_pts comes out to be zero.
Signed-off-by: Sasi Inguva <isasi@google.com>
Reviewed-by: Thomas Mundt <tmundt75@gmail.com>
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
Since af1761f7b5 ffmpeg waits for a frame in each
stream before writing the output header. If we are using threaded decoding for
attached pictures, we have to read till EOF to be able to finally flush the
decoder and output the decoded frame. This essentially makes ffmpeg buffer all
non-attached picture packets, which will cause a "Too many packets buffered for
output stream" eventually.
By forcing single threaded decoding, we get a frame from a single packet as
well and we can avoid the error.
Fixes part of ticket #6375:
ffmpeg -i 46564100.mp3 -acodec libmp3lame -ab 128k -ac 2 out.mp3
Reviewed-by: Hendrik Leppkes <h.leppkes@gmail.com>
Signed-off-by: Marton Balint <cus@passwd.hu>
Josh de Kock
Jan Ekström
Carl Eugen Hoyos
Marton Balint
James Almer
Gyan Doshi
Tobias Rapp
Tomas Härdin
Aman Gupta
Mark Thompson
Jun Zhao
Timo Rothenpieler
Peter Große
Michael Niedermayer
Sasi Inguva