Current code compares the desired recording time with InputStream.pts,
which has a very unclear meaning. Change the code to use actual
timestamps of the frames passed to the encoder.
In several tests, one less frame is encoded, which is more correct.
In the idroq test one more frame is encoded, which is again more
correct.
Behavior with stream copy should be unchanged.
The output is obviously not supposed to contain video (since only
-acodec copy is specified), but that only happens because of the way -t
handling is implemented currently.
Right now those muxers use the default timebase in all cases(1/90000).
This patch avoid unnecessary rescaling and makes the printed timestamps
more readable.
Also, extend the printed information to include the timebases and packet
pts/duration and align the columns.
Obviously changes the results of all fate tests which use those two
muxers.
Return the correct number of consumed bytes and set *data_size = 0.
Returned size is 1 too small, leading to that 1 byte being read as the next
frame, which results in an extra blank frame at the beginning of the stream.
get_ue_golomb_long() is only tested for values up to 2^15 - 2 since
we can not write larger values.
Silence the test on success and return a non-zero value on error.
Use an heap scratch buffer instead of large stack buffer.
Remove unneeded includes.
Codec has only I- and skip-frames, so there is no
need for reget_buffer, change it so it works with
get_buffer.
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
Causes FFmpeg to pass through the correct pts values,
instead of clobbering all to AV_NOPTS_VALUE (the av_init_packet
default) to then make up new ones based on only fps when muxing.
Included are also the related FATE ref changes, which all
some reasonable on quick investigation.
Also set all H.264 references to us -vsync drop to reduce the
diff for the ref files.
Otherwise almost all H.264 references need to change, mostly due
to now starting with negative pts values.
About 20 additional H.264 conformance tests needed -vsync
drop anyway because they create pts values that are out of
order and thus not possible to mux otherwise.
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
Previously the decoder would raise an error.
The end result is the same, the time stamps only change
because regression tests create time stamps incorrectly.
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
They allow to implement the if/then/else logic, which cannot be
implemented otherwise.
For example the expression:
A*B + not(A)*C
always evaluates to NaN if B is NaN, even in the case where A is 0.
(Does not attempt to decode percetual audio data inside.)
Code coverage: libavformat/xwma.c: 3% -> 75%
Signed-off-by: Ronald S. Bultje <rsbultje@gmail.com>
(Don't attempt to decode JPEG data.)
Code coverage: libavformat/smjpeg.c: 0% -> 69%
libavcodec/adpcm.c: 0% -> 10% (fresh run); 92.4% -> 93% following a FATE run
Signed-off-by: Ronald S. Bultje <rsbultje@gmail.com>
The previous sample used for this test only contained type 0 frames.
Replace it with a sample that also features type 1 frames.
Code coverage:
libavcodec/xxan.c: 72% -> 89%
Signed-off-by: Ronald S. Bultje <rsbultje@gmail.com>
Palette is as supposed in native endianness. Converting the pal8 output
to rgb24 is thus necessary for identical CRCs on big and little endian
systems.
The sample has an incomplete last frame. Decoding it is pointless.
The garbage produced was changed by the bitstream reader now
protecting against over-reads.
Signed-off-by: Mans Rullgard <mans@mansr.com>
This patch is a generalization of what Michael Niedermayer
fixed in a single case.
The wmv8-drm fate test had been updated accordingly.
Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
In 1bpp mode, interpret skip&0x80 as "start a new line" instead of "go to next line", this is almost the same except for the first line which was always skipped before and caused to try to write an extra line at the end of the frame (ticket #226).
Signed-off-by: Michael Niedermayer <michaelni@gmx.at>