Use the gcd of all input timebases to ensure PTS accuracy. For the
framerate, just pick the highest of all the inputs, under the assumption
that we will render frames with approximately this frequency. Of course,
this is not 100% accurate, in particular if the input frames are badly
misaligned. But this field is informational to begin with.
Importantly, it covers the "common" case of combining high FPS and low
FPS streams with aligned frames.
In the event that some frame mixes are OK while others are not, the
priority goes:
1. Errors in updating any frame -> return error
2. Any input incomplete -> request frames and return
3. Any inputs OK -> ignore EOF streams and render remaining inputs
4. No inputs OK -> set output to most recent status
This logic ensures that we can continue rendering the remaining streams,
no matter which streams reach their end of life, until we have no
streams left at which point we forward the last EOF.
When combining multiple inputs, the output PTS may be less than the PTS
of the input. In this case, the current's code assumption of always
draining one value from the FIFO is incorrect. Replace by a smarter
function which drains only those PTS values that were actually consumed.
When combining multiple inputs with different PTS and durations, in
input-timed mode, we emit one output frame for every input frame PTS,
from *any* input. So when combining a low FPS stream with a high FPS
stream, the output framerate would match the higher FPS, independent of
which order they are specified in.
Subsequent inputs require frame blending to be enabled, in order to not
overwrite the existing frame contents.
For output metadata, we implicitly copy the metadata of the *first*
available stream (falling back to the second stream if the first has
already reached EOF, and so on). This is done to resolve any conflicts
between inputs with differing metadata. So when e.g. input 1 is HDR and
output 2 is SDR, the output will be HDR, and vice versa. This logic
could probablly be improved by dynamically determining some "superior"
set of metadata, but I don't want to handle that complexity in this
series.
Instead of finding the ref frame in output_frame() and then passing its
signature to update_crops(), pull out the logic and invoke it a second
time inside update_crops().
This may seem wasteful at present, but will actually become required in
the future, since update_crops() runs on *every* input, and needs values
specific to that input (which the signature isn't), while output_frame()
is only interested in a single input. It's much easier to just split the
logic cleanly.
Including the queue status, because these will need to be re-queried
inside output_frame_mix when that function is refactored to handle
multiple inputs.
In anticipation of a refactor which will enable multiple input support.
Note: the renderer is also input-specific because it maintains a frame
cache, HDR peak detection state and mixing cache, all of which are tied
to a specific input stream.
If the input queue is EOF, then the s->status check should already have
covered it, and prevented the code from getting this far.
If we still hit this case for some reason, it's probably a bug. Better
to hit the AVERROR_BUG branch.
We will postpone the vpp session initialization to when input and output
frames are ready, this copy of the sequence parameters will be used to
initialize vpp session.
Signed-off-by: Haihao Xiang <haihao.xiang@intel.com>
- text is now shaped using libharfbuz
- glyphs position is now accurate to 1/4 pixel in both directions
- the default line height is now the one defined in the font
Adds libharfbuzz dependency.
I've been sitting on this for 3 1/2 years now(!), and I finally got
around to fixing the loose ends and convincing myself that it was
correct. It follows the same basic structure as yadif_cuda, including
leaving out the edge handling, to avoid expensive branching.
As we are introducing two new formats and supporting conversions
between them, and also with the existing 0rgb32/0bgr32 formats, we get
a combinatorial explosion of kernels. I introduced a few new macros to
keep the things mostly managable.
The conversions are all simple, following existing patterns, with four
specific exceptions. When converting from 0rgb32/0bgr32 to rgb32/bgr32,
we need to ensure the alpha value is set to 1. In all other cases, it
can just be passed through, either to be used or ignored.
When an option could not be found, print its name and value. Note that
this is not done while applying the options in
avfilter_graph_segment_apply_opts() to give the caller the option of
handling the missing options in some other way.
Niklas Haas
Haihao Xiang
Paul B Mahol
yethie
Philip Langdale
Anton Khirnov